★ State of Arkansas · 6×9 Inch Motorcycle Flag · 2-Ply · 3/8" Mount

Best For: Motorcycles · ATVs & UTVs · Antenna & Flag Mounts · Pig Trail Rides · Talimena Scenic Drive · Bikes Blues & BBQ · Hot Springs Rally · Group Rides · Arkansas Scenic Byways

The 6×9 inch motorcycle flag on a 3/8" sleeve mount is built specifically for sustained highway speed display on motorcycles, ATVs, and UTVs. The 2-ply double-layered knitted polyester construction addresses the specific aerodynamic demands of riding at 55–80 mph — speeds at which standard single-layer flag materials flutter apart within a season of regular use. No grommets, no clips, no hardware to rust or rattle — just a sleeve over your existing flag mount pole.

Motorcycle Flag 6×9 Inch 2-Ply Knitted Polyester Double-Layered 0.75" Sleeve Fits 3/8" Pole

Fly Arkansas's diamond flag at speed with the PromoPatriot Arkansas Motorcycle Flag — a 6×9 inch, 2-ply double-layered knitted polyester flag with a 0.75-inch sleeve that mounts directly on standard 3/8-inch motorcycle flag poles and antenna flag mounts. This flag was designed for the specific demands of sustained highway speed display: the aerodynamic and structural stresses a flag faces at 65–80 mph on a motorcycle are fundamentally different from any other display format in the Arkansas flag lineup, and the 2-ply construction addresses those demands in ways that single-layer materials cannot.

At motorcycle highway speeds, a flag is not flying in a steady breeze — it is cycling through turbulent airflow behind the rider, fairing, and antenna mount. That turbulence creates rapid, repeated snap-load events on the fabric: the flag whips from one side to the other as it moves in and out of the turbulent wake, generating impact forces on the material that are qualitatively different from the steady aerodynamic drag a car window flag or outdoor pole flag experiences. Standard single-layer flag materials — even knitted polyester — fail at the fly edge and seams under this repeated snap-loading within a season of regular highway riding. The 2-ply double-layered construction addresses this directly: two knitted polyester layers bound together create a composite panel with significantly greater resistance to snap-tear failure than either layer alone.

The 2-ply construction also solves the double-sided display problem in a way that single-layer knitted polyester cannot. In a single-layer knitted flag, the open weave of the material allows light and ink from the front-face print to show through to the reverse, producing double-sided display from one layer's print. In a 2-ply flag, each layer carries its own printed face and the two layers are oriented with their print faces outward — so both sides of the flag carry a fully opaque, fully saturated print with no show-through or bleed. The result is genuinely double-sided display at the opacity and color depth that the design requires: Arkansas's white diamond, four stars, and ARKANSAS center band read in full color from either side.

Why Motorcycle Flags Need a Different Construction Than Car Flags

The difference between a car window flag and a motorcycle flag is not just mounting hardware — it is the aerodynamic environment the flag operates in. A car window flag is in relatively clean airflow on the outer side of the vehicle, moving at 25–45 mph with a clear recommendation to remove at highway speed. A motorcycle flag is directly behind the rider and handlebars at 55–80 mph in turbulent wake airflow. The turbulence creates snap-load cycling: the flag repeatedly whips and snaps as it alternates between attached flow and turbulent separation. Each snap event loads the fabric with a brief impact force that far exceeds the steady-state aerodynamic drag. Standard single-layer materials, including single-layer knitted polyester, show fly-edge fraying and seam failures within a season of this loading under regular highway riding. The 2-ply double-layered construction creates a composite panel that distributes snap-load stress across two bonded layers rather than concentrating it in a single layer, dramatically extending the flag's structural life at motorcycle speeds. The 0.75" sleeve mount also contributes: the sleeve attaches to the pole without any hard metal point, distributing the mounting force along the full sleeve length rather than concentrating it at grommet holes, which can tear out under repeated snap-loading.

Perfect For

Motorcycle Highway

Sustained 55–80 mph highway riding — built for the snap-load cycling of turbulent wake airflow at motorcycle speeds.

Pig Trail & Scenic Roads

Arkansas's Pig Trail Byway (AR-23), Talimena Scenic Drive (AR-88), and Highway 7 — Arkansas's premier motorcycle riding routes.

Rallies & Group Rides

Bikes Blues & BBQ (Fayetteville), Hot Springs Motorcycle Rally, and Arkansas group rides — visible Arkansas identity in a pack.

ATVs & UTVs

ATV and UTV flag mounts in Ozark and Ouachita National Forests — same 3/8" pole standard, same 2-ply durability for off-road conditions.

Antenna Flag Mounts

Standard 3/8" antenna flag mounts, CB antenna flag holders, and motorcycle-specific flag pole kits — sleeve fits directly, no hardware needed.

Stationary Display

Rally campgrounds, bike shows, and parking display — flag stays mounted and looks right whether riding or parked.

Mounting on Your Motorcycle or ATV — 3 Steps

Confirm Pole Diameter

Verify your flag mount pole is 3/8" (0.375") diameter. This is the standard for most motorcycle flag poles, antenna flag mounts, and CB antenna flag holders. The 0.75" sleeve is sized for a snug but sliding fit on a 3/8" pole — loose enough to install without tools, tight enough to stay put at highway speed.

Slide Sleeve Over Pole

Orient the flag with the diamond design visible on the front (non-seam) side. Slide the sleeve down over the pole from the top. No clipping, no snapping, no threading required. The sleeve holds the flag upright and allows it to fly free on the fly side.

Seat and Check Fly Clearance

Slide the flag to the correct height on the pole so the fly edge hangs free without contacting any part of the bike, rack, or luggage. At highway speed, the flag will extend rearward and upward. Verify there is nothing behind or above the mount point that the flag could wrap around during riding.

⚠ Sleeve Fit Check — Before Your First Ride

Before riding at highway speed, test the sleeve fit: the flag should slide onto the pole with light hand pressure and hold position when shaken. If the fit is loose enough that the sleeve can slide freely up or down the pole without any resistance, secure the sleeve at the desired position with a small zip tie just above the lower sleeve edge — this prevents the flag from riding up the pole and bunching at the top at speed. If the fit is snug and the sleeve holds position during hand-shake testing, no additional securing is needed.

Arkansas on Two Wheels — The State's Motorcycle Roads and Rallies

Arkansas is widely regarded among riders as one of the premier motorcycle touring states in the country. The Pig Trail Scenic Byway (AR-23 through the Ozark National Forest) is consistently listed among the top motorcycle roads in the United States — 19 miles of tight curves through hardwood forest with minimal traffic. The Talimena Scenic Drive (AR-88/OK-1 along the Ouachita Mountain ridge) offers 54 miles of ridge-running with continuous views into the Ouachita National Forest. U.S. Highway 7 from Russellville to Harrison cuts through the Arkansas River Valley and Ozark plateau for 100+ miles of scenic hill-country riding. On the rally circuit, Bikes Blues & BBQ in Fayetteville is one of the ten largest motorcycle rallies in the United States, drawing hundreds of thousands of riders each October. The Hot Springs Motorcycle Rally brings riders to one of Arkansas's most storied destinations. And across the Ozark and Ouachita National Forests, hundreds of miles of forest roads serve ATV and UTV riders who use the same 3/8" flag mount standard for Arkansas pride on trail rides. Arkansas's diamond flag flying from a motorcycle antenna mount on any of these roads is a statement of where you belong.

6×9 inch motorcycle flag — standard display size for 3/8" motorcycle flag poles, antenna mounts, and ATV/UTV flag holders
2-ply double-layered construction — two knitted polyester layers bonded together for snap-load resistance at motorcycle highway speeds (55–80 mph)
Genuinely double-sided display — each layer carries its own outward-facing print, delivering full-opacity Arkansas design on both faces without show-through or bleed
0.75" sleeve mount — slides over 3/8" poles without tools, clips, or metal hardware; distributes mounting force along full sleeve length rather than concentrating at grommet points
Knitted polyester open weave — reduces aerodynamic drag and allows airflow through the panel, decreasing the snap-load amplitude that tears standard woven flags at speed
Official Arkansas state flag design — white diamond on red field, blue border, four stars, ARKANSAS center band — accurate to the 1913 Hocker design
Compatible with standard motorcycle flag pole kits, antenna flag mounts, CB antenna flag holders, ATV rear rack flag poles, and UTV roll cage flag mounts

Product Name	PromoPatriot Arkansas State Motorcycle Flag 6×9 Inch — 2-Ply Double-Layered Knitted Polyester, 0.75" Sleeve, 3/8" Mount
State	Arkansas (AR)
Flag Design	Official Arkansas State Flag — White Diamond on Red Field, Blue Border, Four Stars, ARKANSAS Center Band — Adopted February 26, 1913
Flag Size	6×9 Inches
Construction	2-Ply Double-Layered — Two Knitted Polyester Layers Bonded Together
Material	Knitted Polyester (2-Ply) — Open Weave, Reduced Aerodynamic Drag
Print Type	Double-Layered Double-Sided — Each Layer Carries Own Outward-Facing Print; Full Opacity on Both Faces
Mount Type	0.75" Sleeve — Slides Over 3/8" Diameter Pole; No Clips, No Grommets, No Metal Hardware
Pole Diameter	Fits 3/8" (0.375") Flag Poles — Standard Motorcycle Flag Pole, Antenna Flag Mount, and ATV/UTV Flag Holder Diameter
Speed Rating	Designed for Sustained Motorcycle Highway Speed (55–80 MPH)
Compatible Mounts	Motorcycle Flag Pole Kits, Antenna Flag Mounts, CB Antenna Flag Holders, ATV Rear Rack Flag Poles, UTV Roll Cage Flag Mounts
Use	Motorcycle, ATV/UTV, Antenna Mount, Rally, Group Ride, Stationary Display
Brand	PromoPatriot — OnlineFlagStore

Standard Shipping

Standard delivery takes 3–5 business days. Expedited (1–2 days) and overnight options available at checkout. Orders placed before 2 PM EST on weekdays ship same day — order before your next ride.
30-Day Hassle-Free Returns

Not satisfied? Return within 30 days for a full refund. Items must be unused and in original condition. Prepaid return label provided. Defects in print, construction, or sleeve replaced free within 30 days — no return required on defective items.
Quality Guarantee

Every PromoPatriot flag is backed against manufacturing defects in print quality and construction. If something isn't right out of the box, we make it right.

Arkansas State Motorcycle Flag 6×9 inch – Double-Layered Printed 2-Ply Durable Knitted Polyester – 0.75 inch Sleeve- Fits on 3/8″ Mount Pole

Name: Get Arkansas 6×9″ Motorcycle Flag Online – Quality & Durability
Price: 10.00 USD
Availability: InStock

$10.00

Compare

Add to wishlist

★ Arkansas Motorcycle Flag · 6×9 Inch · 2-Ply Knitted Polyester · 0.75" Sleeve · 3/8" Mount

Flag Features

2-ply construction engineered for sustained highway speed — snap-load resistant, genuinely double-sided, hardware-free sleeve mount for any 3/8" flag pole

Key Feature

2-Ply Double-Layered

Two knitted polyester layers bonded together into a composite panel that resists the snap-load cycling at motorcycle highway speeds. Single-layer materials — even knitted polyester — fray at the fly edge and seams under repeated snap-loading at 65+ mph. The 2-ply construction distributes snap-load stress across both layers, dramatically extending fabric life.

Both Faces

Genuinely Double-Sided

Each of the two layers carries its own outward-facing print with full opacity — not a single-layer design where ink bleeds through to create a faded reverse image. Both faces display Arkansas's full diamond design in the same saturated color depth. No show-through, no translucency at speed.

Knitted Open Weave

Knitted construction allows air to pass through the panel — reducing solid-surface aerodynamic drag and lowering the peak force of snap-load events at speed. The open weave also means the flag moves with airflow changes rather than resisting them, which is why knitted construction outlasts woven at motorcycle speeds.

Universal Fit

0.75" Sleeve — 3/8" Pole

The 0.75-inch sleeve fits snugly on standard 3/8-inch motorcycle flag poles, antenna flag mounts, CB antenna flag holders, ATV flag poles, and UTV roll cage flag mounts. Slides on without tools or hardware. No grommets, no clips, no metal parts to corrode or rattle at speed.

Highway Speed Rated

Designed for sustained display at 55–80 mph — the speed range where motorcycles cruise on Arkansas highways. The 2-ply composite panel and knitted open weave together address the turbulent wake airflow, snap-loading, and sustained aerodynamic drag that standard flag materials fail under at these speeds within a riding season.

Arkansas

Official Diamond Design

Willie K. Hocker's 1913 Arkansas flag at 6×9 inch riding scale — white diamond on red, four stars, ARKANSAS center band. The high-contrast design is legible from passing lanes and at rally distances. The same accuracy as every flag in the Arkansas lineup, sized for the road.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “Arkansas State Motorcycle Flag 6×9 inch – Double-Layered Printed 2-Ply Durable Knitted Polyester – 0.75 inch Sleeve- Fits on 3/8″ Mount Pole”