Back to products

Click to enlarge

★ State of Florida · 12x18 Inch Boat Flag · 200D Nylon · Brass Grommets · Single Sided Reverse Print

Best For: Boat Rails & Stern Mounts · Pontoon & Kayak Flag Poles · Car Window & Antenna Flags · Golf Cart Whips · Compact Florida Pride Display

The 12x18 inch PromoPatriot Florida State Flag is our smallest, most compact size — purpose-built for boat rail mounts, stern poles, car window flags, and any spot where a full-size flag simply won't fit. Made from genuine 200D nylon with a 100% bleed-through reverse print, solid brass grommets, and stitched edges, this nautical-ready flag is engineered to handle wind whip at marine and highway speeds while keeping Florida's red saltire and seal razor sharp.

12x18 In (1x1.5 Ft) 200D Nylon 100% Bleed-Through Print Brass Grommets Stitched Edges Boat & Marine Ready Fade Proof Colors

Show your Florida pride at sea or on the road with the PromoPatriot Florida State Boat Flag in our 12x18 inch (1x1.5 ft) nautical size. This is our smallest available dimension, purpose-built for boat rail mounts, stern poles, pontoon and kayak flag staffs, car window clips, and golf cart whips — anywhere a standard 3x5 or even a 2x3 flag would be oversized or impractical. Built from genuine 200 Denier (200D) Nylon, it delivers the same heavy-duty commercial-grade fabric used in our larger flags, scaled down to a footprint that's easy to mount anywhere.

This flag uses a single sided design with a 100% bleed-through reverse print. The dye is fully saturated through the 200D nylon weave during printing, so Florida's bold red saltire and detailed state seal read crisp and correct on the front, while the reverse shows a vivid, high-contrast mirror image rather than a faded or washed-out ghost image. At this compact 12x18 size, full ink penetration is essential — it keeps the flag light enough to catch a breeze off the bow while still looking sharp from either side.

Engineered specifically for nautical and vehicle use rather than casual indoor decor, this flag features a reinforced canvas header with solid brass grommets for secure, tear-resistant attachment to boat rail clips, antenna mounts, or stern flag poles. The top, bottom, and fly edges are finished with tight lock-stitching to resist the rapid fraying that smaller flags experience when exposed to boat wake wind, highway speeds, or open-water gusts.

100% Bleed-Through Print vs. Surface Printing — Why It Matters at 12x18

Many small novelty flags use a surface-level print that only coats the top layer of cheap polyester, leaving the backside dull, grey, or nearly blank. At a compact 12x18 size, that flaw is highly visible since both sides are seen constantly while mounted on a moving boat or vehicle. Our 100% bleed-through dye process forces the ink completely through the 200D nylon fibers, so the back is just as vivid as the front. Combined with the tighter weave of 200D nylon, this flag sheds water fast, resists mildew in humid marine air, and holds its color far longer than a typical dollar-bin boat flag.

Perfect For

Boat Rails & Stern Poles

Our most compact size, ideal for rail clips, stern poles, and bow rail mounts on small to mid-size boats.

Car Window & Antenna

A precise fit for window flag clips and antenna mounts without overwhelming your vehicle's profile.

Pontoons & Kayaks

Lightweight enough to fly cleanly from short kayak and pontoon flag staffs without dragging in the water.

Golf Carts & ATVs

A tidy, scaled-right option for whip mounts that won't drag or tangle at low speeds.

Mounting Your 12x18 In Boat Flag — 3 Steps

Unpack & Prep

Unfold the flag and smooth shipping creases by hand, or use a low-heat iron on the "Nylon" setting for a crisp, ready-to-fly look.

Clip to Rail or Mount

Secure the flag to your boat rail clip, stern pole, antenna mount, or window bracket using the brass grommets, checking that clips are tight.

Hoist & Check Clearance

Position the flag so it clears outriggers, antennas, rigging, or car mirrors, allowing it to fly freely without snagging while underway.

⚠ Marine & Highway Speed Advisory

This flag's 200D nylon and lock-stitched edges are built for genuine open-water and roadway use, but sustained exposure to high boat speeds, highway trailering above 50 mph, or severe storm winds will shorten its lifespan. We recommend removing or lowering the flag during fast open-water runs, trailering, and tropical storm conditions.

Florida's Flag — The Sunshine State's Design

Florida's state flag features a red saltire (diagonal cross) on a white field, with the state seal centered at the intersection. The design was adopted in 1900, with the red cross added by popular vote that year specifically so the flag would not be mistaken for a plain white flag of surrender or truce when viewed at a distance — a detail that still matters on open water today. Even at our smallest 12x18 size, the seal—depicting a Seminole woman, sabal palm, steamboat, and the sun's rays—is rendered with sharp, fade-proof clarity thanks to our bleed-through print process.

12x18 Inch (1x1.5 Ft) Florida State Flag — our smallest size, built specifically for boats, cars, and tight mounts.
200D Premium Nylon — durable, water-resistant, and light enough to fly cleanly at marine and roadway speeds.
100% Bleed-Through Reverse Print — full dye saturation for a vivid, high-contrast mirror image on the back, not a faded ghost print.
Solid Brass Grommets — rust-resistant grommets set in a reinforced canvas header for secure rail or window mounting.
Reinforced Stitched Edges — tight lock-stitching on the fly end to resist fraying from boat wake and wind whip.
Fade Proof & UV Resistant — sharp red, white, and seal detail engineered to resist Florida sun, salt air, and humidity.
Nautical & Automotive Versatile — equally suited to a boat rail, kayak staff, car window clip, or golf cart whip.

Product Name	PromoPatriot Florida State Boat Flag 12x18 In — Single Sided Reverse Print, 200D Nylon, Brass Grommets
State	Florida (FL)
Flag Design	Official Florida State Flag — Red Saltire on White Field with Centered State Seal
Dimensions	12 x 18 Inches (1 x 1.5 Feet)
Material	Premium 200 Denier (200D) Nylon
Print Type	Single Sided with 100% Bleed-Through Reverse Print (Reads correctly on front, vivid mirror image on reverse)
Mounting	Canvas header with solid brass grommets
Edge Finishing	Reinforced lock stitching to prevent fraying
Recommended Mount	Boat Rail Clip, Stern Pole, Antenna Mount, Car Window Clip, Golf Cart Whip
Primary Use	Boats, Pontoons, Kayaks, Car Windows, Golf Carts, ATVs
Brand	PromoPatriot

Standard Shipping

Standard delivery 3–5 business days. Expedited (1–2 days) and overnight options available at checkout. Orders placed before 2 PM EST on weekdays ship same day.
30-Day Hassle-Free Returns

Return within 30 days in unused original condition for a full refund. Prepaid return label provided. Manufacturing defects in nylon, stitching, or grommets replaced free within 30 days.
Quality Guarantee

Every PromoPatriot flag is backed against manufacturing defects in color fastness, fabric construction, and grommet integrity. If something isn't right out of the box, we make it right.

Florida State Boat Flag 12×18 Inch – Single Sided with Reverse 100% Bleed-Through Print on Back – 200D Nylon – Brass Grommets – Fade Proof Vivid Colors – Florida Nautical Flag for Boat or Car

Name: Buy Florida 12x18" Boat Flag – Double-Sided Nylon
SKU: B0905
Price: 18.00 USD
Availability: InStock

Single Sided Reverse Bleed | Brass Grommets | 12 × 18 Inch | Fade-Proof Colors | Boat · Car · Outdoor Use

SKU: B0905

$18.00

Compare

Add to wishlist

★ Florida Boat Flag · 12x18 In · 200D Nylon · Brass Grommets · Fade Proof

Flag Features

Compact nautical flag construction — durable 200D nylon, full bleed-through print, and reinforced edges built for boats, cars, and everyday mounts.

Smallest Size

12x18 In Profile

Our most compact flag dimension, purpose-built for boat rails, car windows, and tight mounting spaces.

Marine Grade

200D Nylon Fabric

Water-resistant and quick-drying, built to handle boat wake spray and humid marine air without sagging.

Full Saturation

100% Bleed-Through Print

Dye fully penetrates the nylon weave, giving the reverse side a vivid mirror image instead of a faded ghost print.

Rust-Proof

Solid Brass Grommets

Set in a reinforced canvas header, solid brass grommets give a secure, rust-proof point for rail clips and mounts.

Anti-Fraying

Stitched Edges

Tight lock-stitching along the fly end resists the rapid fraying that boat wake and highway wind cause.

UV Resistant

Fade Proof Colors

UV-resistant dyes keep Florida's bold red saltire and seal detail sharp despite sun, salt spray, and humidity.

Why Choose Us

200D Nylon, Brass Grommets, 100% Bleed-Through Print — A 12x18 Boat Flag Built to Outlast Florida's Waters

A 12x18 flag is almost always mounted on a moving boat, kayak, or vehicle, meaning it endures more constant wind whip and spray than any other size we make. By using 200D nylon, solid brass hardware, full bleed-through dye, and reinforced stitching at this small size, we address the four most common causes of small flag failure: fabric rot, faded backsides, mount tearing, and edge fraying.

PromoPatriot 200D Nylon vs. Standard Cheap Boat Flags

This Product

12x18 In · 200D Nylon · Stitched Edges

200D Nylon — premium weight, sheds spray and rain, resists rot
100% bleed-through print — vivid mirror image on back, no faded backside
Brass grommets — solid brass; won't rust or rip out at rail mounts
Stitched edges — lock stitching stops boat-wake fraying
Fade proof colors — UV treated dyes resist salt air and sun
Flies cleanly — light enough for marine breezes at low boat speeds

Standard Discount Boat Flag

Cheap Polyester · Single Stitch · Flimsy Hardware

100D/150D Polyester — absorbs water, heavy, rots over time
Surface print only — backside is grey, dull, or nearly blank
Tin or plastic grommets — rust quickly, tear out at rail clips
Single stitch — fly end shreds within weeks of boat wind
Untreated dyes — salt air and sun bleach colors fast
Hangs limp — waterlogged polyester won't fly off a rail mount

Feature	PromoPatriot 200D Nylon Boat Flag	Standard Polyester Flag
Material Longevity	200D Nylon — Sheds Spray & Rain, Resists Rot & Mildew	100D Polyester — Absorbs Water, Degrades Quickly
Print Quality	100% Bleed-Through — Vivid on Both Sides	Surface print only — dull, washed-out backside
Wind Performance	Flies cleanly off rails, staffs, and window clips	Heavy fabric hangs limp, wraps around mount
Color Fastness	UV Resistant Dyes — Sharp, Fade Proof Red & White	Untreated ink fades fast in sun and salt air
Mounting Hardware	Solid Brass Grommets in Canvas Header	Cheap tin/plastic grommets that rust and tear

30-Day Satisfaction

Return within 30 days for a full refund if you aren't completely satisfied.

Fast Dispatch

Orders placed before 2 PM EST ship the very same day.

Fade Proof Guarantee

Our 100% bleed-through, UV resistant dye process means your Florida boat flag stays vivid through Florida's intense sun and salt air.

Care & Maintenance

Maximizing the lifespan of your 200D Nylon 12x18 In boat flag

Open Water & Highway Speeds

If mounted on a boat or vehicle, avoid sustained exposure to fast open-water runs or highway speeds (50+ mph) while trailering. In wind speeds exceeding 40 mph or during a tropical storm, lowering or removing the flag is the single best way to prevent edge blowouts.
Rinsing & Cleaning

After saltwater use, rinse the flag with fresh water to remove salt residue, which can stiffen nylon fibers over time. If it accumulates dirt or grime, hand wash with a mild detergent and cold water. Never machine wash or dry, as agitation can damage the grommets and stitching.
Proper Storage

Never fold or store a wet or damp flag — it will develop mildew quickly in humid marine air. Once completely dry, fold it neatly and store it in a dark, dry place away from direct sunlight and away from a damp boat locker.
Monitor the Fly End

The "fly end" (the edge furthest from the mount) is always the first to show wear, especially on a small flag exposed to constant boat wind. Check it periodically. If you notice minor fraying, you can trim the loose thread and re-sew the hem before a full blowout occurs.

Need a larger flag for a residential porch or yard flagpole? Check out our Florida State Flag 3x5 Ft or 2x3 Ft options, made with the exact same premium 200D nylon and brass hardware, scaled up for taller poles.

Shop Florida 3x5 Ft Flag →

12x18Inches

Our smallest flag size, purpose-built for boat rails, car windows, and other compact mounting points.

200DNylon

Premium 200 Denier woven nylon construction, water-resistant and durable for marine and roadway use.

100%Bleed-Through Print

Full dye saturation gives the reverse side a vivid mirror image instead of a dull, faded backside.

FadeProof

UV resistant dyes lock in Florida's bold red saltire and seal detail, keeping colors sharp on the water and road.

Frequently Asked Questions

Everything you need to know about the PromoPatriot Florida 12x18 In Boat Flag

What mounts is a 12x18 inch flag designed for?

A 12x18 inch flag is our smallest size, designed for boat rail clips, stern poles, kayak and pontoon flag staffs, car window clips, antenna mounts, and golf cart whips. It's the right scale for spots where even a 2x3 ft flag would be too large or could drag in the water. If you need something for a residential porch pole, our 2x3 ft or 3x5 ft Florida flags are a better fit.

What does "Single Sided with 100% Bleed-Through Print" mean?

This flag is printed on one side using a dye-sublimation process where the ink fully penetrates, or "bleeds through," the 200D nylon fabric. The front reads correctly with crisp detail, and because the dye saturates the entire fiber, the back shows a vivid, high-contrast mirror image rather than a dull or washed-out reverse. This is different from cheap surface-printed flags, where the backside often looks grey or blank.

Will this flag hold up on a boat at speed?

Yes, the 200D nylon and lock-stitched edges are built for real marine use, including boat wake wind and open-water gusts. That said, sustained exposure to very high boat speeds, highway trailering above 50 mph, or severe storm conditions will accelerate wear on any flag. We recommend lowering or removing the flag during fast runs, trailering, and tropical storms to maximize its lifespan.

Can I use this as a car window or antenna flag instead of a boat flag?

Absolutely. The 12x18 inch size and brass grommets work just as well clipped to a car window flag holder or antenna mount as they do on a boat rail. The same durable 200D nylon and fade-proof print hold up well at highway speeds for everyday driving use, though we still recommend removing it before long highway trips at sustained high speed.

How do I clean this flag after saltwater use?

Rinse the flag with fresh water after saltwater exposure to remove salt residue, which can stiffen the nylon fibers over time. For deeper cleaning, hand wash in cool water with a mild, bleach-free detergent, then air dry completely before re-mounting or folding for storage. Avoid machine washing or drying, which can damage the grommets and stitched hem.

What is your return policy?

You can return the flag within 30 days in original, unused condition for a full refund — a prepaid return label will be provided. If the flag has a manufacturing defect, such as a misset grommet, misprinted colors, or unraveled stitching out of the box, we will replace it free of charge within 30 days. Normal outdoor and marine wear, such as edge fraying from sustained wind or color fading after months of sun and salt exposure, is the expected lifecycle of a flag and is not covered as a defect.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “Florida State Boat Flag 12×18 Inch – Single Sided with Reverse 100% Bleed-Through Print on Back – 200D Nylon – Brass Grommets – Fade Proof Vivid Colors – Florida Nautical Flag for Boat or Car”